Availability: | |
---|---|
EN 50181 Plug-in type bushings above 1kV up to 52kV and from 250A to 2.5kA for equipment other than liquid filled transformers
EN 50180 Bushings above 1kV up to 36kV and from 250A to 3.15kA for liquid filled transformers
HD629.1 Test requirements on accessories for used on power cables of rated voltage from 3.6/6(7.2)kV up to 20.8/36(42)kV-Part 1:cables with extruded insulation
IEC 60502.4 Power cable with extruded insulation and their accessories for rated voltages from 1kV(U=1.2kV)up to 30kV(U=36kV)-part 4:test requirements on accessories for cable with rated voltages from 6kV up to 30kV(U=36kV)
lEc60099 Metal oxide surge arresters without gaps for a.c.systems
JB/T 8952 Polymer-housed metal oxide surge arresters without gaps for a.c.systems
IEEE 386 Separable insulated connector system for power distribution system above 600V
GB11032 Metal oxide surge arresters without gaps for a.c.system
JB/T 8952 Polymer-housed metal oxide surge arresters without gaps for a.c.systems
35kV Rear connector with surge arrester Suitable for 35kV electrical systems, extend to instal in the front connector or behind the connector for the electrical equipment.And provide over voltage protection.
35kV Rear connector with surge arrester adopt the flood proofing design, is fully insulated, fully shielded and all sealed products. The resistors inside of surge arrester has good nonlinearity.so the arrester with low residual voltage, large capacity, fast response time, steep wave flat, effectively prevent the lightning strikes and switching impulse and has good over-voltage protection, to ensure transmission operation.
Note: The product meets the requirements of IEC 60502.4, GB / T12706.4.
EN 50181 Plug-in type bushings above 1kV up to 52kV and from 250A to 2.5kA for equipment other than liquid filled transformers
EN 50180 Bushings above 1kV up to 36kV and from 250A to 3.15kA for liquid filled transformers
HD629.1 Test requirements on accessories for used on power cables of rated voltage from 3.6/6(7.2)kV up to 20.8/36(42)kV-Part 1:cables with extruded insulation
IEC 60502.4 Power cable with extruded insulation and their accessories for rated voltages from 1kV(U=1.2kV)up to 30kV(U=36kV)-part 4:test requirements on accessories for cable with rated voltages from 6kV up to 30kV(U=36kV)
lEc60099 Metal oxide surge arresters without gaps for a.c.systems
JB/T 8952 Polymer-housed metal oxide surge arresters without gaps for a.c.systems
IEEE 386 Separable insulated connector system for power distribution system above 600V
GB11032 Metal oxide surge arresters without gaps for a.c.system
JB/T 8952 Polymer-housed metal oxide surge arresters without gaps for a.c.systems
35kV Rear connector with surge arrester Suitable for 35kV electrical systems, extend to instal in the front connector or behind the connector for the electrical equipment.And provide over voltage protection.
35kV Rear connector with surge arrester adopt the flood proofing design, is fully insulated, fully shielded and all sealed products. The resistors inside of surge arrester has good nonlinearity.so the arrester with low residual voltage, large capacity, fast response time, steep wave flat, effectively prevent the lightning strikes and switching impulse and has good over-voltage protection, to ensure transmission operation.
Note: The product meets the requirements of IEC 60502.4, GB / T12706.4.
content is empty!
Email: jonsonchai@chinahaivo.com
Wechat:+86 13587716869
WhatsApp:+86 13587716869
Tel: 0086-577-62836929
0086-577-62836926
0086-13587716869
0086-15957720101